Hardware

Kit includes: Two Curved Washer for 1 1/2" Pipe Two 1 3/8 x 4 Delrin Spacer Two 3/8-16 x 8" SS Threaded Rod Two 3/8-16 SS Cap Nut Two 3/8-16 SS Nylon Locknut Two 3/8 SS Flat Washer Two 3/8 Nylon Shoulder Bushing Two 3 1/2" Backup Plates

Solid-state DC fan controller. Excellent for varying the speed of DC fans to control the amount of airflow. Will work on Fans from 12 to 24 VDC, rated up to 6 Amps. Rotary adjustment to vary the speed 0 -100%. Removable input terminal block makes wiring snap. Connection points for input and output wires are clearly marked. Dimensions: 3.5"(L) x 2.35" (W) x 2.25" (H) (including knob). Mounting holes on 1.6" x 3.1" centers

Cable Clam 0.83" Provides a waterproof pass-through for antenna cables without requiring removal of the factory installed connector Perfect for antenna installation Waterproof co-axial installation without removing connectors Save the expense of removing and replacing connectors Avoid poor connections from removing factory connectors For use above the waterline only Manufacturer Part # 1002 Specifications Max Cable Diameter 0.44in (11.18mm) Max Connector Diameter 0.83in (21.08 mm) Body...

These are designed to fit a 1.5" schedule 40 pipe.  A 3/8" through hole in the center. It is made of anodized aluminum.  Bright dip anodized to a marine grad standard.

The ConnectPro system has superior electric current carrying capacity that eliminates problems that rob motors of power and reduce battery life.  The ConnectPro system has features not found on other trolling motor connections: Exclusive Marine-grade turn locking connection Weather resistant seals and covers safeguard electrical contacts from water and corrosion Universal design works with 12, 24, 12/24, 24/36, 36 Volt combinations Accepts up to 8 Gauge wire Works for any 2 or 3 wire...

Gemini Side Mounts were developed to provide a range of connections for grab rails and attachments on dodgers and biminis. Sliding mounts provide a cleaner look at a lower cost. Split type mounts, since they can be placed anywhere on a frame, allow a broader range of applications.

Sold in sets of 4. Anodized aluminum Z shapped bracket with multiple hole for easy mount of solar panels.

Gemini Side Mounts were developed to provide a range of connections for grab rails and attachments on dodgers and biminis.   Sliding mounts provide a cleaner look at a lower cost.  Split type mounts, since they can be placed anywhere on a frame,  allow a broader range of applications.

Smaller Solar PV Modules    Universal "Z" Mount Brackets Attaches to any solar module frame, perfect for curved or irregular surfaces. Kit includes four (4) Anodized Aluminum Z brackets and four (4) stainless steel bolts.

GEMINI 1"  Stainless Steel Concaved Fork MountPart # GEMCON-1-F

GEMINI 1"  Stainless Steel Concaved Post Mount Part # GEMCON-1-P

1 inch Stainless Steel Take-Apart Jaw Slide

Uses 9/64 drill bit for #8 screw or fastener   Features: Swing-open design, drill on installed frames, on radiused corners, anywhere.  Large knurled brass thumbscrews for a sure grip. Tool steel drill bushing for lifetime use. Rugged cast bronze body will not mar tubing. Applications: Drill stainless tubing easily Install fasteners of all types Add padeyes for tensioning straps Replace set screws with secure fasteners ...

This is a handy must-have tool for anybody working with solar panels that utilize MC-4 type connectors. Dual fork allows for easy release of connectors once the connectors have been engaged while the opposite end is used to help tighten down connector bushings. Made of nonmetallic material which makes them very durable in a Marine or wet environment.  Sold in Pairs.

Stainless Steel U-bolt Perfect for clamping onto a 1" stainless steel Bimini or stanchion pipe on board your vessel. Features a 1/4-20 thread with 1" ID and comes with to stainless steel nuts. Overall length is 2". Sold individually.

Stainless Steel Cap Nut for use with  1/4-20 bolt thread

Adjustable Panel Support - used in our stanchion mounting kits to hold in place the solar panel once the pivot angle has been set. Also useful for other functions onboard a boat where temporary support is needed.  Length can be adjusted from 24" to 47"

Stainless Steel End Cap for 1" Tube (each).  Push in friction ears  hold-in-place.  No tools required.

316 Grade Stainless Steel Tube 1\" Tube, 8' in length.

1" rail clamps (sold as set of 2).  These are a great hardware product for mounting almost any item to a 1 inch stainless steel rail that might be on your boat. They clamp on using a slotted captive screw and secure to your item with three mounting holes (#8).   Rail Clamp Spacer is also available.  For more information click here.

• Quick mount clamps require no holes to be drilled in railings for installation• Clamps mount to the railings simply by tightening the wing nut• Fits any .75", 1" OR 1.25" railings• Quick release design allows items to be quickly and easily removed for storage• Use for all sorts of accessory installations, including glass racks, binocular holders, bottle holders, and other similar items• Two (2) per package Clamp dimensions are 4" x 1.5" x 1.5"   Rail Clamp Spacer is also...

This is a handy must-have device for anybody working with solar panels that utilize MC-4 type connectors. It provides protection for any idle MC-4 connector from weather and dirt. Great accessory for winter storage when panels are removed to cap off the feed wires. Sold in Pairs (1 male + 1 female). ** IMPORTANT ** MC4 Connectors not included

Replacement option for Germini mounts