Air X Marine Parts

Complete Set of Three balanced blades for use on Air 30 & Air 403 (also used on Air-X Land and Marine.) Black color only and sold in set of 3. Part # 2-ARBL-101-01

Air X Cruisers Spare Part includes Nose Cone, Blades, and Bolt Pack. If you are planning to cruise offshore or go on a long distance cruise this is a must-have kit on board in order to keep your wind generator functioning successfully. Nose cones and blades can easily be damaged from flying debris or birds and require replacement which can be easily done.

Air-X Marine / Air 403 Replacement Nose Cone. Bolt package sold separately  Part # 3-CMBP-1007-02

Stop/Run  Switch - (50 ADC) DC rated & Sealed

Run/Stop Switch with Face Plate, 15' 14-3 wire and interconnect terminal block for use with 3 phase wild AC wind generator 400W or less. It allows remote wind generator Stop/ Run switch to be located in an easy to access area.

Stop/Run Switch (50A DC) Sealed w/Legend Plate, Transient Suppressor & Crimps for Hook Up

Stop/Run Switch Legend Plate

BEARING - SHIELDED  Replacement inside Axis bearing for Air X, Air Breeze, Air 30, Air 40, Silent Wind & Air 403 wind generators. (1) Sealed/Shield Bearing Only

e10 Control PanelWind Turbine Control Panel If you need to control both wind and solar see our e20 PANEL models. The e10 Wind Turbine Control Panel  It is pre-engineered to make wiring the wind turbine easy - just attach two wires from your battery  and two wires from the turbine to the large clearly labeled terminals. It could not be simpler. The flush mount panel includes a pre-wired "Stop / Run Switch" with noise suppressors, Digital Power-Energy Meter (displays Voltage, Current...

This heavy duty plastic electronics enclosures is made with acrylonitrile butadiene styrene (ABS).  It meet IP54 standard, and the Watertight Version meets IP65 standard.  This enclosure has an UL 94 HV Flammability rating. This enclosure comes with its  faceplate cut out to meet the requirements for the e10 panel allowing for direct drop-in mounting. In also  provided are 2 wire bushing and 6 matching sets of hardware to mount the e10 analog meter. There are no pre-drilled...

BEARING - SHIELDED & SEALED  - Replacement  inside Axis bearing  for Air X, Air Breeze, Air 30, Air 40, Silent Wind & Air 403 wind generators.  (1) Sealed/Shield Bearing Only Part # 3-CABR-1002

Control Board for Air-X 12V.  Part # 2-ARCT-101-03  Serial Number 68835-Current** This item is non-returnable/non-refundable. **

Control Board for Air-X 24V.  Part # 2-ARCT-101-05** This item is non-returnable/non-refundable. **

Control Board for Air X 48V.  Part # 2-ARCT-101-06** This item is non-returnable/non-refundable. **

The bearing spacer is 2 mm thick that sits between the front and internal axis bearings on the Air series of wind generators and SilentWind turbine products.  Sold as individual items, but 2 are required to meet the wind turbines 4 mm thickness on all products. Please order 2 at a time for full bearing spacer replacement. Part Number: 3-CAOT-1227

Yaw Bearing Kit includes a replacement sealed  bearing; "o" ring replacement for face assembly, large and small snap rings, armature connection screws, tye wraps; tube of Tef-Gel and application swab.Part # 2-ARYW-100-02 enhanced featured

All-inclusive HEAVY DUTY bearing replacement kit for AIR wind generators (Air Breeze or Air-X). This bearing kit is designed for wind generators that are installed in high wind or continuous wind environments where normal bearing wear is unacceptable. The Kit includes all the necessary parts that need replacement including the very important “O” ring that allows for resealing of the nacelle from the environment. Removal of bearings can be difficult at time based on the age of the unit and its...

The spacer bearing is 2 mm thick that sits between the front and internal axis bearings on the Air when generators and SilentWind turbine products.  Sold as individual items, but to a required to meet the wind turbines 4 mm thickness on all products. Please order 2 at a time for full bearing spacer replacement. Part Number: CAOT-1005

Yaw Neoprene Pad sits between the yaw mounting clamp and mast to help provide vibration dampening.  Fits most wind generators that mount on to a 1.5" schedule 40 pipe (OD 1.9"). Neoprene Yaw Pad (2" X 6" X .13" Thick) for Air Breeze (Marine & Land), Air-X (Marine & Land), Air 40, and Air 30 Part # 3-CAOT-1022

Stator for- Air Breeze 12V- Air-X 24V- Air 30 24V  - Air 40 12V   Part # 3-CMBP-1019-02

Stator for Air X or Air30  12V.  Part # 3-CMBP-1019-01

AIR Breeze, AIR X, AIR SILENT X  Yaw Assembly.  Includes Complete Marine Yaw Shaft Assembly with 34" Wire Length.  Manufacturer Part # 2-ARYW-101-02

Stator for - Air Breeze 24V- Air X 48V- Air 30 48V- Air 40 24V  Part # 3-CMBP-1019-03

Air X (Land & Marine) or Air 30 Bolt Package for Blade Mounting Includes:- Socket Head Screws - Nylon Lock Nuts- 3 Allen Keys- Tef-Gel - Nut Jam 5/8"-18 Zinc(also used on Air-X Land)Part # 3-CMBP-1023-01

AIR Hub Rotor Jam Nut. Land and Marine; Includes 5/8-18 19-8 Stainless Steel Hub Rotor Jam Nut Part # 3-HDNT-912

AIR Brush Kit. Land and Marine; Includes Brushes and Springs (also Air Industrial Brush Kit) Part # 2-ARCT-100

This high tech wind generator Blade Kit  allows for upgrade of all  existing Air Breeze, Air-X, Silent Air-X, Air-30, Air-40, Silentwind wind generators (12-24-48V) to the latest in high performance blades. The trendy distinctive Blue-White-Gray colored high-tech carbon fiber blades maximizes the capturing of wind energy with minimal noise.  The Wind Generator Blade Kit includes 3 balanced carbon fiber blades that are Blue with White and Gray stripes. Included in...

Replacement O-ring that sits between the face and body of the wind generator.  Provide a watertight seal to the internal circuits and should be replaced whenever the body and face plate is opened up.   Part # 3-CAOT-1002

Marine Casting Face. (Air Breeze) Part # 3-CMBP-1003-02

Replacement Hub for Air-X Marine.  Part # 3-CMBP-1005-02