MC4 Wires Products

The 10-2 AWG Marine grade wire is terminated with a male and female MC4 connector at one end and  flying leads at the opposite end.  Both tinned wires run in a single cable covered by a UV resistant sheath.  Allows for easy connection of solar panels that have factory terminated MC4 leads eliminating the need for special tools.  Great for installation on boats or near salt water enviorments.  Custom lengths available, please call for a quotation.

The 10-3 AWG Marine grade wire is terminated with a male and female MC-4 connector and a flying lead terminated with a ring crimp for frame ground connection at one end and flying leads at the opposite end.This cable allows for easy connection of solar panels that have factory terminated MC four type connectors minimizing installation time or the need for special tools.The additional ground lead easily connects to the frame of the solar panel providing a grounding wire within the same cable....

The 10 AWG Marine grade wire is terminated at each end with a uninsulated soldered ring crimp with a #10 hole used to act as a interconnect grounding of solar panel frames.Hardware included. Great solution for the installation of solar on a boat or near a salt water environment

MC4 - #10 Wire Solar Panel Cable Land Based This cable is recommended for land based installations only and is used with the Kyocera and BP solar panels as well as other panels that take the MC-4 Connections. This is a single conductor cable that has a male and female MC-4 connector terminated at each end. The most common use of this cable is to cut it in half creating a feeder line that would interconnect from the solar panel + and - feeds directly into the solar charge controller....

MC4 MARINE Black Extension Cable is terminated with a male and female MC –4 type connector. Typically used to extend the solar panel flying leads to another where the panels are not mechanically in close proximity to make the connection.Tinned copper cable is used to assure long-term use aboard a boat in a marine environment.

3 Stage MC4 Parallel Connectors (Set of 2). These connectors are designed for up to 1,000 volts and 30 Amps. Manufacturer: Solarland Manufacturer Part # SLCBL-48

3 Stage MC4 Parallel Connectors (Set of 2).These connectors are designed for up to 1,000 volts and 30 Amps.Manufacturer: SolarlandManufacturer Part # SLCBL-48

MC4 Parallel Connectors Y Style Male/Female Branch Set (Set of 2).These connectors are designed for up to 1,000 volts and 30 Amps.Manufacturer: SolarlandManufacturer Part # SLCBL-46

MC4 Parallel Connectors for Three Solar Panels, Flexible X-Style, 1 Positive 1 Negative (Set of 2). These connectors are designed for up to 1,000 volts and 25A. Manufacturer: Solarland Manufacturer Part # SLCBL-49

MC4 - #10 Male Connector This item is used with the Kyocera and BP solar panels as well as other panels that take the MC-4 Connections.

MC4 - #10 Female Connector This item is used with the Kyocera and BP solar panels as well as other panels that take the MC-4 Connections.

White Color Cable Gland This Cable Feed Gland is designed to enable the cable from a solar panel to enter a roof, and to ensure that the routing hole is fully sealed against water ingress. To fix, simple clean the surface where the centre support rails are to be used, then bond the profiles using Sika Flex 252, 291 or similar (not included). These connectors are designed for up to 1,000 volts and 30 Amps. Specifications Dimension 3.54"(L) x 3.94"(D) x 1.97"(H) 90(L) x 100(D) x 50(H)mm Cable...

Black Color Cable GlandThis Cable Feed Gland is designed to enable the cable from a solar panel to enter a roof, and to ensure that the routing hole is fully sealed against water ingress.To fix, simple clean the surface where the centre support rails are to be used, then bond the profiles using Sika Flex 252, 291 or similar (not included).These connectors are designed for up to 1,000 volts and 30 Amps.SpecificationsDimension3.54"(L) x 3.94"(D) x 1.97"(H)90(L) x 100(D) x 50(H)mmCable...

This is a handy must-have tool for anybody working with solar panels that utilize MC-4 type connectors. Dual fork allows for easy release of connectors once the connectors have been engaged while the opposite end is used to help tighten down connector bushings. Made of nonmetallic material which makes them very durable in a Marine or wet environment.  Sold in Pairs.

This kit should be used when installing any panel with MC4 or TYCO connections on a boat to ensure reliability of product.

This is a handy must-have device for anybody working with solar panels that utilize MC-4 type connectors. It provides protection for any idle MC4 connector from weather and dirt. Great accessory for winter storage when panels are removed to cap off the feed wires.Sold in Pairs (1 male + 1 female). ** IMPORTANT ** MC4 Connectors not included