e Marine

The 10-2 AWG Marine grade wire is terminated with a male and female Multi-Contact PV Connector at one end and  flying leads at the opposite end. Both tinned wires run in a single cable covered by a UV resistant sheath. Allows for easy connection of solar panels that have factory terminated Multi-Contact PV Connector leads eliminating the need for special tools. Great for installation on boats or near salt water environments. Custom lengths available, please call for a...

Rolling Portable Power Pack with AC inverter plus folding portable 90W solar panel for recharging The power pack is self-contained with a built-in battery, AC inverter w 2 AC outlets and control  panel all packaged into a wheeled container with handle. The emergency backup system can power light loads such as: cell phone chargers, TVs, radios, computers, high-efficiency lamps and other 120 VAC items or even used to start your car.  The solar panel kit plugs into the Power...

4KW Inverter Powered System With 2.3 kW of SolarAll-inclusive kit (except batteries) ready for installation on rooftop. Features 8 fixed frame high efficient solar panels interconnected in to a master power panel that features a 4000W inverter, circuit breakers, battery monitor and solar charge controller. Backup Grid Tie Kit with Solar Features: 2300 W of solar (8 panels) 100A MPPT Solar charger Auto bypass power assembly panel by Magnum Power 4000 Watt, 120 V, 60 Hz inverter Battery fuel...

Solar panels continue to produce high voltages even with a limited amount of sunlight. Solar circuits on board a boat should be protected with a disconnect to allow safe servicing of equipment. e Marine is pleased to be able to offer this installation kit that allows the solar circuit to be disconnected from the charge controller. The circuit breaker allows for quick disconnect of the solar panels when you are off the boat providing additional safety. This breaker box comes with a warning...

12V Battery Charger Kit (recommended to be used with 120 amp/hr battery bank or less)When you purchase one of our kits you will receive the solar panel complete with mounting hardware to clamp the solar panel onto a standard 1\" stainless steel rail; 15' marine grade wire with water tight quick connector for easy connect/disconnect hook up (easy stowage of solar panel); Solar Charge Controller; line fuse; ring and butt splice crimps and a detailed hookup diagram.

Brushed anodized aluminum 9 ft or 11 ft pre drilled mast, 1.5" Sched 80, and two 8 foot (1") stays  (used with MKW01105).  Our special interior coated vibration absorption coating can be applied on the mast to reduce noise.    Recommended for use on wind generators up to 400 Watts and weigh under 30 pounds.For more information on how the mast coating work, please click here. ...

Stop/Run  Switch - (50 ADC) DC rated & Sealed

Run/Stop Switch with Face Plate, 15' 14-3 wire and interconnect terminal block for use with 3 phase wild AC wind generator 400W or less. It allows remote wind generator Stop/ Run switch to be located in an easy to access area.Good for use on Rutland 1200 and Silent Wind Generators only.

Solar panels continue to produce high voltages even with a limited amount of sunlight. Solar circuits on board a boat need to be protected with a disconnect to allow safe servicing of equipment. e Marine is pleased to be able to offer this installation kit that allows the on board solar circuit to be disconnected from the charge controller. The circuit breaker (s) allows for quick disconnect of the solar panels when you are off the boat providing additional safety. This breaker box comes with...

The 10-3 AWG Marine grade wire is terminated with a male and female Multi-Contact PV Connector and a flying lead terminated with a ring crimp for frame ground connection at one end and flying leads at the opposite end. This cable allows for easy connection of solar panels that have factory terminated Multi-Contact PV Connector type connectors minimizing installation time or the need for special tools. The additional ground lead easily connects to the frame of the solar panel providing a...

600 to 800 A-Hr 24V AGM Battery Systems600 A-Hr/24 V AGM battery system kit includes six (6) Power King Batteries and seven (7) #4/0 x 12” long terminated ring crimps wires.800 A-Hr/24 V AGM battery system kit includes eight (8) Power King Batteries and ten (10) #4/0 x 12” long terminated ring crimps wires.All-inclusive kit (except batteries) ready for installation on rooftop. Features 8 fixed frame high efficient solar panels interconnected in to a master power panel that features a 4000W...

The 10-3 AWG Marine grade wire is terminated with a male and female MC-4 connector and a flying lead terminated with a ring crimp for frame ground connection at one end and flying leads at the opposite end. This cable allows for easy connection of solar panels that have factory terminated MC four type connectors minimizing installation time or the need for special tools. The additional ground lead easily connects to the frame of the solar panel providing a grounding wire within the same cable....

This kit will work on 12, 24 or 48V systems and includes a bluetooth enabled Victron charge controller for easy set up and monitoring. The pre-designed kit  is an easy way to add Solar power to your boat without the guess work. Works great on boats equipped with electric drives. The kit is designed to be installed in 1" existing bimini frame. (7/8" available only as Special Order). Kit includes: 2 Solarland 200 W solar panels with Cross Kits for each panel Solar 150/35 MPPT Smart ...

MTS70 Power Energy Meter w/20A Shunt The Power Energy Meter (PEM) is a unique, 2 inch round, marine grade energy meter designed to monitor power and energy production of onboard renewable energy devices, such as solar panels and wind turbines. e Marine is pleased to offer the MTS-70, Marine industries first power-energy meter capable of monitoring energy produced by onboard systems such as wind turbines and solar panels. Exclusively developed to our specifications this meter monitors battery...

All the hardware to install your own wind turbine mast and stays.  You must supply the 1.5" ID (schedule 40 pipe) mast and two 1" stay SS pipes (rercommend 8' long).  Included in this great kit is only the hinged isolated mast base, two isolated stay tie mounts and related  hardware to install the mast. This kit is recommended for use with the Air Breeze, Air X, Airdolphine, Rutland 913/914i wind turbines. Custom fabricated masts are available to meet your specific needs....

Solarland SL90 (GE) Standard Mount Kit Single or Dual Rail

These pre-assembled 12V Battery Charger Kits are excellent solutions for quickly installing a small solar system on board small fishing, power and sailboats for an easy recharging system. Connection is simple, wire the 15' cables two leads to the 12 V battery. Each kit has its own built-in three stage charge controller and is fused. Never worry about overcharging your battery or about having the batteries dead when you are ready to take the boat out for the weekend.Solar charge controller...

The Multi-Contact PV Connector 10 AWG Marine grade wire is terminated at each end with a uninsulated soldered ring crimp with a #10 hole used to act as a interconnect grounding of solar panel frames. Hardware included. Great solution for the installation of solar on a boat or near a salt water environment

Multi-Contact PV Connector MARINE Black Extension Cable is terminated with a male and female Multi-Contact PV Connector type connector. Typically used to extend the solar panel flying leads to another where the panels are not mechanically in close proximity to make the connection.Tinned copper cable is used to assure long-term use aboard a boat in a marine environment.

400 to 600 A-Hr 48V AGM Battery Systems 400 A-Hr/48 V AGM battery system kit includes eight (8) Power King Batteries and eight (8) #4/0 x 12” long terminated ring crimps wires. 600 A-Hr/48 V AGM battery system kit includes twelve (12) Power King Batteries and twelve (12) #4/0 x 12” long terminated ring crimps wires. All-inclusive kit (except batteries) ready for installation on rooftop. Features 8 fixed frame high efficient solar panels interconnected in to a master power panel that features a...

This heavy duty plastic electronics enclosures is made with acrylonitrile butadiene styrene (ABS).  It meet IP54 standard, and the Watertight Version meets IP65 standard.  This enclosure has an UL 94 HV Flammability rating. This enclosure comes with its  faceplate cut out to meet the requirements for the e10 panel allowing for direct drop-in mounting. In also  provided are 2 wire bushing and 6 matching sets of hardware to mount the e10 analog meter. There are no pre-drilled...

30 Amp Surface Mounted Circuit Breaker

Solarland SL90 (GE) Cross Mount Kit Single or Dual Rail

Solar PV Dual Circuit Disconnect allows an easy and safe means to turn off/on and disconnecting the vessel solar array. This is extremely important when the high voltage solar system becomes necessary to reset the charge controller or for servicing. The solar PV single string disconnect is rated up to 16A on systems up to 300 VDC. It is strongly recommended on solar system voltages above 48 VDC. This disconnect features a dual (2 pole) switch, which disconnects both the plus and a...