e Marine

Solarland SL90 (GE) Standard Mount Kit Single or Dual Rail

The 10-3 AWG Marine grade wire is terminated with a male and female Multi-Contact PV Connector and a flying lead terminated with a ring crimp for frame ground connection at one end and flying leads at the opposite end. This cable allows for easy connection of solar panels that have factory terminated Multi-Contact PV Connector type connectors minimizing installation time or the need for special tools. The additional ground lead easily connects to the frame of the solar panel providing a...

These pre-assembled 12V Battery Charger Kits are excellent solutions for quickly installing a small solar system on board small fishing, power and sailboats for an easy recharging system. Connection is simple, wire the 15' cables two leads to the 12 V battery. Each kit has its own built-in three stage charge controller and is fused. Never worry about overcharging your battery or about having the batteries dead when you are ready to take the boat out for the weekend.Solar charge controller...

The Multi-Contact PV Connector 10 AWG Marine grade wire is terminated at each end with a uninsulated soldered ring crimp with a #10 hole used to act as a interconnect grounding of solar panel frames. Hardware included. Great solution for the installation of solar on a boat or near a salt water environment

Multi-Contact PV Connector - #10 Wire Solar Panel Cable Land Based This cable is recommended for land based installations only and is used with the Kyocera and BP solar panels as well as other panels that take the Multi-Contact PV Connections. This is a single conductor cable that has a male and female Multi-Contact PV Connector terminated at each end. The most common use of this cable is to cut it in half creating a feeder line that would interconnect from the solar panel + and...

e10 Control PanelWind Turbine Control Panel If you need to control both wind and solar see our e20 PANEL models. The e10 Wind Turbine Control Panel  It is pre-engineered to make wiring the wind turbine easy - just attach two wires from your battery  and two wires from the turbine to the large clearly labeled terminals. It could not be simpler. The flush mount panel includes a pre-wired "Stop / Run Switch" with noise suppressors, Digital Power-Energy Meter (displays Voltage, Current...

e10 Control PanelWind Turbine Control Panel If you need to control both wind and solar see our e20 PANEL models. The e10 Wind Turbine Control Panel  It is pre-engineered to make wiring the wind turbine easy - just attach two wires from your battery  and two wires from the turbine to the large clearly labeled terminals. It could not be simpler. The flush mount panel includes a pre-wired "Stop / Run Switch" with noise suppressors, Digital Power-Energy Meter (displays Voltage, Current...

Multi-Contact PV Connector MARINE Black Extension Cable is terminated with a male and female Multi-Contact PV Connector type connector. Typically used to extend the solar panel flying leads to another where the panels are not mechanically in close proximity to make the connection.Tinned copper cable is used to assure long-term use aboard a boat in a marine environment.

400 to 600 A-Hr 48V AGM Battery Systems400 A-Hr/48 V AGM battery system kit includes eight (8) Power King Batteries and seven (7) #4/0 x 12” long terminated ring crimps wires.600 A-Hr/48 V AGM battery system kit includes twelve (12) Power King Batteries and twelve (12) #4/0 x 12” long terminated ring crimps wires.All-inclusive kit (except batteries) ready for installation on rooftop. Features 8 fixed frame high efficient solar panels interconnected in to a master power panel that features a...

This heavy duty plastic electronics enclosures is made with acrylonitrile butadiene styrene (ABS).  It meet IP54 standard, and the Watertight Version meets IP65 standard.  This enclosure has an UL 94 HV Flammability rating. This enclosure comes with its  faceplate cut out to meet the requirements for the e10 panel allowing for direct drop-in mounting. In also  provided are 2 wire bushing and 6 matching sets of hardware to mount the e10 analog meter. There are no pre-drilled...

30 Amp Surface Mounted Circuit Breaker

Solarland SL90 (GE) Cross Mount Kit Single or Dual Rail

Rolling Portable Power Pack with AC inverter plus folding portable 160W solar panel for recharging The power pack is self-contained with a built-in battery, AC inverter w 2 AC outlets and control panel all packaged into a wheeled container with handle. The emergency backup system can power light loads such as: cell phone chargers, TVs, radios, computers, high-efficiency lamps and other 120 VAC items or even used to start your car.  The solar panel kit plugs into the Power Pack...

70 Amp, surface mount with trip-reset lever

Solar PV Dual Circuit Disconnect allows an easy and safe means to turn off/on and disconnecting the vessel solar array. This is extremely important when the high voltage solar system becomes necessary to reset the charge controller or for servicing. The solar PV single string disconnect is rated up to 16A on systems up to 300 VDC. It is strongly recommended on solar system voltages above 48 VDC. This disconnect features a dual (2 pole) switch, which disconnects both the plus and a...

Solarland SL160 Standard Mount Kit Single or Dual Rail.Disclaimer: Image shown is not for the actual product.

Solarland SL160 Cross Mount Kit Single or Dual Rail. Disclaimer: Image shown is not for the actual product.

600 - 800 A-Hr 24V LiIon Battery System600 A-Hr/24 V LiIon battery system kit includes four (4) ReLion Batteries and two (2) #4/0 x 12” long terminated ring crimps wires.800 A-Hr/24 V LiIon battery system kit includes one (1) ReLion Battery. No cables included.All-inclusive kit (except batteries) ready for installation on rooftop. Features 8 fixed frame high efficient solar panels interconnected in to a master power panel that features a 4000W inverter, circuit breakers, battery monitor and...

40 Amp, surface mount with trip-reset lever

200 - 600 A-Hr 48V LiIon Battery System200 A-Hr/48 V LiIon battery system kit includes 400 A-Hr/48 V LiIon battery system kit includes 600 A-Hr/48 V LiIon battery system kit includes one (4) ReLion Batteries and two (2) #4/0 x 12” long terminated ring crimps wires.All-inclusive kit (except batteries) ready for installation on rooftop. Features 8 fixed frame high efficient solar panels interconnected in to a master power panel that features a 4000W inverter, circuit breakers, battery monitor...

We are pleased to offer a series of low cost analog control panels to support on-board wind turbines. It is easy to install and will result in a professional operator station enhancing the beauty and value of your vessel, RV or remote home . It helps to reduce installation costs and makes wiring a snap with just 4 wires to connect. The e10 panel is available in four sizes (5A, 10A, 25A & 40A) that will support 12-48V DC system.The e10 CONTROL PANEL operates and monitors the wind turbine. It is...

https://www.emarineinc.com/LG-...These electric drive charging kits are plug and play systems designed for charging 48VDC systems using a MPPT Solar charge controller to regulate and maximize the solar array energy. There are three kits available with varying solar arrays. Included is a Bluetooth enabled feature that allows direct connection to your smart phone for easy setup and monitoring of system performance. These kits require a hard flat area to mount the solar panels .68kW Charging Kit...

Mast Mounting Kit: All the hardware to install the Typmar  wind turbine including 7'4" - 1.5" diameter brushed aluminum  mast with vibration absorbing internal coating  and two 8'  stainless steel 1" stays and isolated connection point mounting hardware.  Each mast is e Marine fabricated  to include the necessary holes for easy installation,  pre welded Typmar flange adaptor ring that includes easy connect terminal blocks for simple wiring hook up and...

50 Amp, surface mount with trip-reset lever