Wind Turbine Accessories

Land Casting Face. (for Air 30 and Air 40) Part # 3-CMBP-1003-01

The ConnectPro system has superior electric current carrying capacity that eliminates problems that rob motors of power and reduce battery life.  The ConnectPro system has features not found on other trolling motor connections: Exclusive Marine-grade turn locking connection Weather resistant seals and covers safeguard electrical contacts from water and corrosion Universal design works with 12, 24, 12/24, 24/36, 36 Volt combinations Accepts up to 8 Gauge wire Works for any 2 or 3 wire...

Includes 1.5 ML of Tef Gel and applicator   Part # 3-CAOT-1015

Complete Set of Three balanced blades for use on Air 30 & Air 403 (also used on Air-X Land and Marine.) Black color only and sold in set of 3. Part # 2-ARBL-101-01

Air X Cruisers Spare Part includes Nose Cone, Blades, and Bolt Pack. If you are planning to cruise offshore or go on a long distance cruise this is a must-have kit on board in order to keep your wind generator functioning successfully. Nose cones and blades can easily be damaged from flying debris or birds and require replacement which can be easily done.

Air Breeze Cruisers Spare Part includes Nose Cone, Blades, and Bolt Pack.

Complete set of three blades for use on Air Breeze (Marine & Land) and Air 40. Bolt Package included. Black color and sold in set of 3. Part # 2-ARBR-101

Replacement Nose Cone for Air Breeze Marine/Next Generation Air Breeze,  (white color)   Part # 3-CMBP-2015-02

Air-X Marine / Air 403 Replacement Nose Cone. Bolt package sold separately  Part # 3-CMBP-1007-02

Stop/Run  Switch - (50 ADC) DC rated & Sealed

Run/Stop Switch with Face Plate, 15' 14-3 wire and interconnect terminal block for use with 3 phase wild AC wind generator 400W or less. It allows remote wind generator Stop/ Run switch to be located in an easy to access area.Good for use on Rutland 1200 and Silent Wind Generators only.

Stop/Run Switch (50A DC) Sealed w/Legend Plate, Transient Suppressor & Crimps for Hook Up

Stop/Run Switch Legend Plate

This heavy duty plastic electronics enclosures is made with acrylonitrile butadiene styrene (ABS).  It meet IP54 standard, and the Watertight Version meets IP65 standard.  This enclosure has an UL 94 HV Flammability rating. This enclosure comes with its  faceplate cut out to meet the requirements for the e10 panel allowing for direct drop-in mounting. In also  provided are 2 wire bushing and 6 matching sets of hardware to mount the e10 analog meter. There are no pre-drilled...

We are pleased to offer a series of low cost analog control panels to support on-board wind turbines. It is easy to install and will result in a professional operator station enhancing the beauty and value of your vessel, RV or remote home . It helps to reduce installation costs and makes wiring a snap with just 4 wires to connect. The e10 panel is available in four sizes (5A, 10A, 25A & 40A) that will support 12-48V DC system. The e10 CONTROL PANEL operates and monitors the wind turbine. It...

All-inclusive HEAVY DUTY bearing replacement kit for AIR wind generators (Air Breeze or Air-X). This bearing kit is designed for wind generators that are installed in high wind or continuous wind environments where normal bearing wear is unacceptable. The Kit includes all the necessary parts that need replacement including the very important “O” ring that allows for resealing of the nacelle from the environment. Removal of bearings can be difficult at time based on the age of the unit and its...

Marine Casting Face. (Air Breeze) Part # 3-CMBP-1003-02

Blocking diode isolation kit includes a easily mountable diode block along with (2) 12 – 10 gauge push-on crimps and hook up instruction sheet making installation a snap. A single stainless steel screw is required for mounting (not included). Rated 25A -400VRecommended for use with Rutland wind turbine controllers when the solar PV option is utilized.

Rutland Wind Generator Replacement Blade (each). Fits 913, 914i, FM910-3, FM 910-4 and 910-Mark 2.Installation screws not included. Related Items:Blade Fasteners for Rutland 913/914i Blades

25 Amp 600 Piv Bridge Rectifier P.I.V. 1 1/8" square.

6 pin terminal block with barriers, clamping screws and see-through cover (included).  Rated at 25A, 50 V DC it provides an excellent solution for interconnect of large cables to small interface connections on small clamping terminal blocks found on the HRSi wind turbine regulator manufactured by Rutland.  We strongly recommend  this when large wires are used on the installation as a means of interconnecting to the controller to eliminate installation and operational...

Pin crimps allows easy termination of either 12 or 10gauge wire.  They feature a single pin that extends off the end of the crimp often required for interconnect to clamp type terminal blocks.  This makes for an excellent solution to difficult tight  wiring situations by eliminating the typical flying wire strands  when trying to insert stranded cables in a small tight clamping terminal strip.  These are strongly recommended for use with the HRDi wind charger...

25 Amp 600 Piv Bridge Rectifier P.I.V. 1 1/8" square.